I,Function basic principle
Using the thermoplastic sheet is heated and softened in the mildew for vacuum molding, turn out to be needed merchandise. Their function is the clip – heating – forming – merchandise.
II,Features
01. CZPT, pneumatic, electrical integration. Each motion system controlled by the PLC. Contact-screen procedure, straightforward and convenient.
02. Loading simpler, considerably less scrap molding material financial savings.
03. Heater motor, frequency handle, high-velocity exact and stable.
04. CZPTtric furnace temperature management technique is entirely computerized smart computerized compensation control, partitioning a managed man-equipment interface of a electronic enter, with higher precision fine-tuning, temperature uniformity, quick heating (just five minutes from -400 levels), stable ( influence from exterior voltage, temperature fluctuations of not more than one diploma), reduced vitality intake (saving about 15%), extended lifestyle plate stove, electric bricks etc. automatically detected.
05. Suited convex molding, molding top, steady solution top quality.
06. The mould seat with electric limit adjustment, modify swiftly and very easily.
07. Device is equipped with air-cooling technique that permits goods to great quicker and greater styling.
08. Creation counts, or can be set to automatically shut down forward of the law enforcement, with file memory purpose, can store up to 230 merchandise parameter info
09. The die desk employing mosaic lubricated bearings, freedom of motion and accurate.
ten. Die clip structure actions and synchronized by the rack and pinion composition linkage, the lifting synchronization, extending cylinder daily life
11. Working side employing security grating gadgets to ensure the protection of the operator misuse.
III,CZPT parameters
Parameter | XCH130/one hundred ten/13.five(method No.) | |
Max. forming location (mm2) | 1300mm*1100mm | |
Min.forming spot (mm2) | 1200mm * 1000mm | |
Sheet technical specs (Max.) | 1370mm * 1170mm | |
Thickness of sheet applied | .eight-3mm | |
Max. molding height | 135mm | |
Capacity | one-three (times/min) | |
Fuel source | Air consumption (m3/min) | ≥ two |
Pressure | .6Mpa(inlet .eight-1Mpa) | |
Vacuum pump (Outlay) | Busch R5 5710 | |
Power | 3-stage 4-wire 380V / 220V 50Hz | |
CZPT power | 64KW | |
Dimensions ( L × W × H) (mm) | 4200 * 2410 * 2900 | |
Total fat (Kgs) | 4000 |
IV,CZPT configuration
Programmable logic controller (PLC) | ZheJiang Delta |
Contact display keep track of (10.4 “inch / Shade) |
ZheJiang Delta |
CZPT | ZheJiang Delta |
Feeding motor | China |
Heater (99pcs) | China |
Sound state relay AC contactor | Germany Siemens |
Thermo relay | Japan Omron |
Vacuum pump | Busch R5 5710 |
pneumatic components | South Korea |
Cylinder | China |
Fan blower | China |
V,Installation Directions
1. The equipment must be put in in a dry, thoroughly clean store ground. And leave some aside set up location of the energetic operating length fuel, electricity, refer to the machine diagram of a flat placement.
two. After getting rid of the packaging machine, placed on the floor level of the company can use. Its location, see the physical appearance of room dimensions Figure II.
three. Ended up related to a resource of h2o and fuel supply, and link the ground wire.
four. Verify heater heating aspects are intact (Ruoyin shipping and delivery hurt should be replaced).
5. All lubrication factors should be added to lubricants. Vacuum pumps, air supply FRL oil stage ought to occur on to the line. The watershed of the filter device slop put the net.
six. Check out the vacuum pump motor, cooling enthusiast rotation is right (following energy take a look at, which if not appropriately swap two wires can).
seven. CZPT component of the user’s equipment to set up their possess gas purification gear, in purchase to make sure enhanced service existence of pneumatic factors. You should refer to the pneumatic tools thoroughly clean air system flow chart diagram III.
eight. Exterior electrical power cable with double insulated copper wire four, every single segment is not significantly less than 16mm2.
VI,Sample Photo
VII,Certifications
VIII,Workshop Photos
IX,Package deal
X,Exhibition