Tongke SN Horizontal Double Suction Break up casing Centrifugal Pump for hydraulic projects
Design SN pump is a single-stage double-suction horizontal split centrifugal pump and employed to transportation pure water and the liquid of each physical and chemical character equivalent to those of h2o, the highest temperature of which need to not be in excess of 80 ºC.
Gain have to say √
1. Mild responsibility, Conserve cost √
two. Good security and easy installation √
three. exceptional hydraulic functionality, Substantial efficiency. √
four. Prolonged time Bearing’s provider existence. √
five. Excellent NSK SKF bearing and Burgmann mechanical seal √
six. DIN, ANSI CZPT optional for your specifications. √
Procedure Parameter
Diameter | DN 150-1200 mm |
Ability | no more than 11500m3/h |
Head | no much more than 120m |
Liquid Temperature | up to80 ºC |
Software Fields
Appropriate for water source and drainage in factories, mines, towns and electric powered stations, waterlogged land drainage and irrigation of farming land and carious hydraulic initiatives
Structural Drawing
one | Casing | 2 | Protect | 3 | Impeller | four | Shaft | 5 | Double-suction seal ring |
six | Shaft sleeve | 7 | Packing sleeve | eight | Packing | 9 | Packing ring | 10 | Packing gland |
eleven | Shaft sleeve nut | twelve | Bearing physique | 13 | Fixing screw | fourteen | Gland of bearing physique | 15 | Bearing |
16 | Cluth | 17 | Bearing finish include | eighteen | water retaining ring | 19 | stud | 20 | Essential |
Record of Major Parts Substance
Part name | Substance | GB CZPT |
Pump casing | Forged iron/Ductile iron/Cast metal/ CZPT metal | HT 250/QT400-eighteen/ZG230-450/& as customers request |
Impeller | Bronze/Forged iron/Bronze/brass/CZPT steel | ZCuSn10Pb1/Ht 250 ZCuZn16Si4/& as consumers ask for |
Shaft | CZPT steel/CZPT steel | 2Cr13/40Cr |
seal-ring on pump casing | Bronze/Solid iron/Brass/CZPT steel | ZCuSn10Pb1/HT 250/ZCuZn16Si4/& as consumers ask for |
More particulars about our Horizontal Double Suction Break up casing Centrifugal Pumps make sure you contact with Tongke’s engineer.
Each inlet and outlet of this pump are put underneath the axial line, horizontally and vertical to the axial line, the pump casing is opened in the middle so it is unneeded to get rid of the water inlet and outlet pipelines and motor(or other primary movers). The pump moves CW viewing from the clutch to it. The pump relocating CCW can also be created, but it need to be specially mentioned at order.
The principal components of the pump are: pump casing(one), pump cover (two), impeller(3), shaft(four), dual-suction seal ring(5), muff(six), bearing( 15) etc. and all of them, other than the axle which is produced of top quality carbon steel, are made of forged iron. The substance may be changed with other people upon distinct media.
The pump is pushed straight by indicates of connecting to it through an elastic clutch. (Set up a stand furthermore in scenario of a rubber band driving).
The shaft seal is packing seal and, to awesome and lubricate the seal cavity and stop air from receiving into the pump, there is a packing ring amongst the packing. A small quantity of higher stress h2o flows into the packing cavity by way of the tapered beard throughout the pump’s doing work to act as a water seal.
Both pump casing and go over form the doing work chamber of the impeller and there are threaded holes for mounting vacuum and stress meters on the flanges at the two inlet and outlet and for h2o draining on the decrease facet of them.
The impeller is static-equilibrium calibrated, fixed with the muff and the muff nuts in equally sides and its axial place can be modified via the nuts and axial drive gets balanced by means of the symmetrical arrangement of its blades, there may possibly be residual axial pressure which is borne by the bearing at the axle conclude. The pump shaft is supported by two one-column centripetal ball bearings, which are mounted inside of the bearing entire body on each ends of the pump and lubricated with grease. The dual suction seal ring is employed to minimize the leak at the impeller.
√ Note before buy
Parameters essential to be submitted at purchase
1. Pump product and the flow, head (such as the method reduction), NPSHr at the level of the desired working condition.
two. Variety of shaft seal (should be observed possibly mechanical or packing seal and, if not, supply of the mechanical seal construction will be produced).
3. Moving course of the pump (need to be noted in circumstance of a CCW installation and, if not, delivery of a clockwise set up will be produced).
4. Parameters of the motor (Y series motor of IP44 is typically used as the reduced-voltage motor with a electricity <200KW and, when to use a high voltage one, please note its voltage, protective rating, insulation class, way of cooling, power, number of polarity and manufacturer).
5. The supplies of pump casing, impeller, shaft and so forth. components. (shipping and delivery with the CZPT allocation will be produced if with out becoming observed).
six. Medium temperature (shipping and delivery on a continual-temperature medium will be created if without having becoming mentioned).
seven. When the medium to be transported is corrosive or is made up of sound grains, please note the attributes of it.
CZPT certificate
Company Impression
Provider
Twenty several years style and engineering expertise and A lot more than ten several years more than sea marketplace Encounter. Tongke give most specialist and thoughtful Pre-income and Soon after services.
CZPT training CZPT analysis
Set up and debugging Troubleshoot
Maintenance Update and advancement
Dedication to the service
one.One particular-12 months guarantee. Supply specialized assist free all-lifestyle of the products.
two.Preserve all-lifestyle getting in contact with with clients, get comments on use of the products and make the products high quality constantly perfected.
3.Sizzling-line of services is obtainable in 24h, responded in 8h.
Your call and mail is welcome at any time
SN Horizontal Double Suction Split casing Centrifugal Pump for hydraulic initiatives
Get in touch with | Mr Seth Chen |
Phone | -13817768896 |